What did you do to your Trailboss today? 🛠️

[Alopez2588]

Plastic dip Z71, it was kinda a pain in the ass. Didn’t peel off as easy as I hoped.

 

[tbuss5831]

Today I debadged my truck. In my opinion I think it looks a hell of a lot better and cleaner. Next I want tires/small lift.

 

[treadhead]

Took it out and got it dirty on a walk in the clouds!

 

[Will]

2 weeks old. Did a few things...
Full Ceramic Tint.
Rhino Lining Bed
Folding Bed Cover
Black Badges
King 2.5 Set up
Camburg Kinetic UCA's
Method 312 17x9 -12
BFG K02 35x12.5x17
Wheel Well Trim
.50 cal Antenna
Rugged Radio set up

Good times.....

 

[DevOps260]

Go Rhino RB20 Running Boards

 

[tbuss5831]

2 weeks old. Did a few things...
Full Ceramic Tint.
Rhino Lining Bed
Folding Bed Cover
Black Badges
King 2.5 Set up
Camburg Kinetic UCA's
Method 312 17x9 -12
BFG K02 35x12.5x17
Wheel Well Trim
.50 cal Antenna
Rugged Radio set up

Good times.....

Ok I love your truck. Do you have an y issues with rubbing?

 

[Will]

Ok I love your truck. Do you have an y issues with rubbing?

Yes. We trimmed the mud flap and a decent amount off the bottom of the inner felt liner and that took care of it. If I really get after it though it’ll rub on that little black frame extension. So to remedy, I may cut it at a 45 degree angle to give it that final clearance and weld a patch on it to cover.

 

[danh63]

Are a lot of people Wrapping their front ends? If so, what is that costing to do?

 

[MJ$]

Ready lift 1.75” kit with UCAs and 285/75/18 Nitto Ridge Grapplers. It also has Amp power boards and a couple other little things here and there.

View attachment 149

Whats the ready lift. It goes on top of 2 inch factory lift

 

[MJ$]

Ordered a Roto-Fab Cold Air Intake System today! I will be sure and post a review and pictures after I get it installed.
I'm anxious to get it on and experience the improved sound, performance (seat of my pants anyway) and fuel economy...and of course the great looks of this quality component!!

How is it

 

[Spyderwebb]

How is it

See my post on this thread on Nov 19th.

To update further I would say that I continue to be very pleased with the intake, had to tighten it down again after a road trip but that is normal after initial installation. Fuel economy has stayed about the same but the seat of my pants performance feels it is an improvement. Great sound too, probably why the fuel economy has not improved (always have my foot in it), love the growl! Looks great too!!

It's a keeper!!

 

[MJ$]

Thanks man. Gonna get one and maybe programmer

 

[Snowman1322]

View attachment 283View attachment 285View attachment 286View attachment 287
Go Rhino RB20 Running Boards

I did the exact same boards. Love them so far

 

[Pointman921]

Plastic dip Z71, it was kinda a pain in the ass. Didn’t peel off as easy as I hoped.

Any idea how well it holds up through snow/ice and car washes?

 

[JonSnow]

Any idea how well it holds up through snow/ice and car washes?

Over time it will peel off. I have Plastidiped lots of things. Looks good for a while but eventually comes off especially in a car wash. I would highly recommend just getting new black emblems.