What's new

What did you do to your Trailboss today? 🛠️

~Installed aftermarket Soler Throttle Body
~Powerstop Z36 Extreme Truck Brake Pads
~MSD Coil Packs
~MSD Spark Plug Wires
~Jet Performance MAF Sensor
 

Attachments

  • 20250927_111915.webp
    20250927_111915.webp
    174.1 KB · Views: 27
  • 20250927_123217.webp
    20250927_123217.webp
    166.3 KB · Views: 30
  • 20250927_123012.webp
    20250927_123012.webp
    214.2 KB · Views: 32
  • 20250927_123128.webp
    20250927_123128.webp
    310.9 KB · Views: 35
  • 20250927_111903(1).webp
    20250927_111903(1).webp
    207.2 KB · Views: 33
  • 20250927_111915.webp
    20250927_111915.webp
    174.1 KB · Views: 35
  • 20250927_122956.webp
    20250927_122956.webp
    370 KB · Views: 19
  • 20250927_123918.webp
    20250927_123918.webp
    266.8 KB · Views: 20
  • 20250927_112144.webp
    20250927_112144.webp
    220.7 KB · Views: 17
  • 20250927_123021.webp
    20250927_123021.webp
    227.9 KB · Views: 33
I only have 350 miles on my 2025 6.2 TB, but had running boards installed so my Wife can climb in easily. Had the bed Line-X coated. Next is installing the 360 degree GM camera system.
 
View attachment 22911Took a pic next to an OG 2500 Trailboss😂
A friend of mine had one way back when. There was so much room in the engine compartment he would climb in there to work on the 350. It had "3 on the tree". The throw from 1st to 2nd seemed like it was two feet!
 
A friend of mine had one way back when. There was so much room in the engine compartment he would climb in there to work on the 350. It had "3 on the tree". The throw from 1st to 2nd seemed like it was two feet!
Still plenty of room in there with a BBC. Granny four speed, 2wd, and the big block; she’s a pulling work in progress
 
Removed the black bezel exhaust tips and replaced them with dual outlet tips. Actually made the sound a bit more throaty. Sounds pretty good.
 

Attachments

  • 20251005_135322(1).webp
    20251005_135322(1).webp
    306.4 KB · Views: 36
  • 20251005_134957.webp
    20251005_134957.webp
    528.9 KB · Views: 40
  • 20251005_134947(1).webp
    20251005_134947(1).webp
    282.6 KB · Views: 40
  • 20251005_125857.webp
    20251005_125857.webp
    325.5 KB · Views: 43
  • 20251005_125847(1).webp
    20251005_125847(1).webp
    251.8 KB · Views: 39
  • 20251005_125838(1).webp
    20251005_125838(1).webp
    394.6 KB · Views: 38
Removed the black bezel exhaust tips and replaced them with dual outlet tips. Actually made the sound a bit more throaty. Sounds pretty good.
I’ve seen those RC tips before on American trucks website. If you wanted to tuck them in for a more flush look would you have to cut your muffler tips? Or are they adjustable some how?
 
I’ve seen those RC tips before on American trucks website. If you wanted to tuck them in for a more flush look would you have to cut your muffler tips? Or are they adjustable some how?
Yes, you would need to trim back the "stock" tailpipe tips a few inches because as is, they do stick out approximately 3-4 inches. You can only push them on over the muffler tips so far.
 
Last edited:
I’ve seen those RC tips before on American trucks website. If you wanted to tuck them in for a more flush look would you have to cut your muffler tips? Or are they adjustable some how?
Something needs to be done. The exhaust looks bent and broken as is.
 
Something needs to be done. The exhaust looks bent and broken as is.
The stock pipes angle down and the factory tips mount to the bumper and not the exhaust pipe. That's what makes it nearly impossible to just slap another set of tips on. The rear exhaust hangers don't help either. Also the pipe isn't round, it's actually somewhat oval. I measured it a while back hoping to use some of the other tips I have. Between the bumper opening and pipe size, none would work. I just put stock type black tips on.
 
The stock pipes angle down and the factory tips mount to the bumper and not the exhaust pipe. That's what makes it nearly impossible to just slap another set of tips on. The rear exhaust hangers don't help either. Also the pipe isn't round, it's actually somewhat oval. I measured it a while back hoping to use some of the other tips I have. Between the bumper opening and pipe size, none would work. I just put stock type black tips on.
I removed my stock tips and replaced them with RC tips. I do not mind that the RC tips stick out a few inches. I actually like the look. If I get tired of the look, I may put the stock black bezel tips back on. Haha!
 

Attachments

  • 20251005_135322(1).webp
    20251005_135322(1).webp
    306.4 KB · Views: 14
  • 20251005_134957.webp
    20251005_134957.webp
    528.9 KB · Views: 23
  • 20251005_125847(1).webp
    20251005_125847(1).webp
    251.8 KB · Views: 20
  • 20251005_125838(1).webp
    20251005_125838(1).webp
    394.6 KB · Views: 16

Latest Discussions...

Back
Top